![]() The official example bat file does have 230 set as frequency and the readme mentions 200 MHz as example, but it also includes the following line “All X6 low power miner must set the ltc-clk lower than 248”. The miner is interesting, because in it there is a little something about the recommended frequencies, something that should be included with the ZeusMiner product information like a recommended frequency to reach the advertised hashrate. The Raspbian installation doesn't have any issues with the Wifi dongle either plugged into the 2nd port on the rPi or on the hub or chained from a root hub on another hub (same dongle on both, the small $12 (USD) wifi from /newark/element14).It seems that Zeus has updated their cgminer 3.1.1 fork with support for the ZeusMiner Scrypt ASICs with a version for the new X6 low power miners, though it should also be compatible with the previous miners as well. See my post here, - it's my MinePeon setup (and you'll see the small Raspbian setup there as well), I put a message at the bottom about USB Wifi. Should it make any problems that the wifi is on the same hub as the miners? I have yet to find info on autostart since I can't get it to call by itself and go and add more difficulty to the mix. I've gotten ticked for the night and plugged them back into my pc. It's probably just me getting greeted with the pi's limitations but when I plug my powered hub in 2 usually don't light and the 3rd I have is solid light and none are noticed and even when they are, I call "sudo cgminer" and it asks for questions of what to connect to and closes. 1 amps of wiggle room.Īt this point your better off you didn't. Factor in the 700mA needed, then factor in 3 amps provided by a specific model DLINK 7 port USB HUB, you now can only run 4 BE's on this Hub. I would not recommend running a rpi on off the same powered hub as your BE's, doing so you limit how many BE's you can run. If you have a 20 Port USB Hub with a 5 amp power supply you will only ever get 5 BE's working, unless you hardware hack the hub to 10 amps, but that may start melting components. You can find bigger hubs that support more ports but pay attention to the Power it delivers to each port. You use 1 USB port off the rpi for the 1st DLINK hub, 6 BE's plug in leaving 1 USB port to chain to the next HUB. If you are going to use a wifi adapter make sure it is verified to be compatible. 1 rpi with A/C Power adapter, either using wireless or wired network. One possible optimal setup for a single rpi and 10 BE's is might be this, and will be my setup once my DLINK Hubs arrive. See my write up at the end of this thread: You really need to pay attention to is power, for the rpi and the BE's themselves. ![]() I can't think of a reason to upgrade really, perhaps if new BE's come out and CGminer is updated to support them. It's been humming along for over a week now. I'm back to using 3.1.1 from that Tutorial and have zero issues. cgminer -o -u -p " from the cgminer-3.4.3 folder it will launch and start using any BE's you have recognized by the rpi OS. I also am not sure if PiMiner will work with the newer versions of cgminer, it may require modification and I'm no Programmer. However the last part ">/dev/null 2>&1&" I'm not sure what it does or if it is needed with the newer cgminer. The command to start running with all BE's attached should be something like this for the auto start command. They dropped the need for the "-S /dev/ttyUSB#" after 3.1.1.Īlso the configure and make commands do still work, however I don't believe the configure command is necessarily needed since after 3.1.1 cgminer is setup to recognize and run BE's. The only problem I ran into was getting 3.4.3 working with the LCD Plate, and the auto run at boot up. I have successfully substituted version 3.4.3 using that tutorial. So they will have access to the latest and most accurate information and thereby assisting the crypto-community at large. We created this website with the sole purpose of users being able to search quickly and efficiently in the field of cryptocurrency Your personal data, therefore, will never be in jeopardy since we are not asking for any of your data and you don't need to provide them to use our site with all of its capabilities. The aim of our project is to create a faster website that yields more results and faster without having to create an account and eliminate the need to log in. However, our experience and user feedback led us create our site īitcointalk's search is slow, and difficult to get the results you need, because you need to log in first to find anything useful - furthermore, there are rate limiters for their search functionality. ![]() It was the Bitcointalk forum that inspired us to create - Bitcointalk is an excellent site that should be the default page for anybody dealing in cryptocurrency, ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |